China E-link China Technology Co.,LTD Company News

E-link Launches LNK-IMC306P PoE+ and LNK-IMC306 Industrial Ethernet Switches E-link, a trusted manufacturer of industrial networking equipment, is pleased to announce the availability of two hardened Ethernet switches built for mission-critical deployments: the LNK-IMC306P Series Industrial PoE+ Switch and the LNK-IMC306 Series Industrial Ethernet Switch. Both models pack six 10/100Base-TX copper ports plus three 100Base-FX fiber uplinks into a compact aluminum housing, making them ideal for factory floors, transportation systems, security networks, and outdoor cabinets. LNK-IMC306P Series — Power and Data Over a Single Cable The LNK-IMC306P Series is a 6-port 10/100Base-TX plus 3-port 100Base-FX hardened PoE switch. It supports IEEE 802.3af/at PoE+ with up to 30W per port, allowing Powered Devices such as IP cameras, wireless access points, VoIP phones, and sensors to receive both power and data over standard RJ-45 cabling. By eliminating separate power runs, installers reduce cabling cost and shorten deployment time in hard-to-reach locations. 6 x 10/100Base-TX + 3 x 100Base-FX Full/half-duplex, auto-negotiation and auto MDI/MDI-X on all RJ45 ports IEEE 802.3af/at PoE+ with 30W maximum per port 48~57VDC redundant power input via 6-pin terminal block -40°C to 80°C (-40°F to 176°F) operating temperature LNK-IMC306 Series — Reliable Non-PoE Connectivity The LNK-IMC306 Series delivers the same rugged six-copper/three-fiber configuration without PoE, drawing just 5W and accepting a wide 12~48VDC input range. It is the efficient choice for data-only aggregation, where powered devices are supplied locally or PoE is not required. 6 x 10/100Base-TX + 3 x 100Base-FX SFP, SC, FC and ST optical interfaces available 12~48VDC redundant power input IEEE 802.3az Energy Efficient Ethernet (EEE) IEEE 802.3x flow control Shared Industrial-Grade Design Both switches share a common foundation engineered for harsh conditions. A fanless aluminum case dissipates heat and resists vibration, shock, and electromagnetic interference. Redundant power inputs guard against single-source failure, while store-and-forward switching, a 1024-entry MAC address table, and a 512K-bit packet buffer keep traffic flowing smoothly. The switches operate from -40°C to 80°C and store at -40°C to 85°C, with 5% to 95% non-condensing humidity and an MTBF exceeding 200,000 hours. Specification LNK-IMC306P Series LNK-IMC306 Series Copper Ports 6 x 10/100Base-TX (PoE+) 6 x 10/100Base-TX Fiber Ports 3 x 100Base-FX (SFP/SC/FC/ST) 3 x 100Base-FX (SFP/SC/FC/ST) PoE Standard IEEE 802.3af/at, 30W per port N/A Input Power 48~57VDC, redundant 12~48VDC, redundant Power Consumption 180W max (PoE in use) 5W max Operating Temperature -40°C to 80°C -40°C to 80°C Dimensions (WxDxH) 150 x 115 x 50 mm 150 x 115 x 50 mm Mounting DIN-Rail DIN-Rail Compliance and Applications Both series are manufactured under ISO 9001 and meet EN55022 Class A, EN55024, and a full suite of IEC 61000-4 immunity standards including ESD, radiated susceptibility, EFT, surge, conducted susceptibility, and power frequency magnetic field. Available models cover multimode dual-fiber SC at 2KM, single-mode dual-fiber SC at 20KM, single-mode single-fiber SC at 20KM, and single-mode single-fiber FC at 20KM, plus SFP variants for flexible optical selection. Typical deployments include industrial automation, intelligent transportation, video surveillance, power utilities, and outdoor wireless backhaul — anywhere a dependable, wide-temperature switch is essential.

With the continuous increase in network demands for industries, new energy, and outdoor projects, ordinary switches are difficult to meet the requirements of wide-voltage power supply, remote monitoring, and adaptation to harsh environments. An AI PoE Switch is essential for ensuring stability and reliability in these scenarios. The LNK-AIMC104GMP is an industrial AI PoE Switch independently developed by E-link, specifically designed for harsh conditions. It integrates the convenience of non-managed switches with the intelligent management capabilities of managed switches, providing an integrated solution for on-site network construction. What is LNK-AIMC104GMP The LNK-AIMC104GMP is an industrial PoE+ switch with a boost circuit. Its hardware configuration includes 4 Gigabit PoE Ethernet ports and 1 SFP optical uplink port. It supports the IEEE 802.3af/at standard and has a maximum output power of 30W per port. The AI PoE switch comes with an LED display and is equipped with an Android APP and web management interface. Without the need for additional detection tools, it can complete device status reading and parameter configuration, suitable for low-voltage input scenarios such as solar power supply, and can cope with various difficult industrial network environments. Working Principle The AI PoE switch is equipped with its own self-developed intelligent management system and voltage boost module. After inputting a 9-54V DC voltage, the boost circuit converts the input voltage into a PoE standard 48V output. Different input voltages correspond to different total PoE power of the entire machine. The AI PoE switch completes PoE device detection, classification, and power supply output through the hardware chip, while continuously collecting operating data such as voltage, current, temperature, and SFP optical module DDM optical power. The data is synchronized and pushed to the LED screen, mobile APP, and web interface. Functions such as fiber link alarm, timed restart, and VLAN isolation are realized through the built-in firmware. In redundant link mode, link failures will automatically switch to the backup link to ensure the network does not disconnect. Installation and Use Mount the switch onto the DIN rail, ensuring there is sufficient ventilation space for the aluminum casing; Connect the 9-54V DC power terminal, confirm normal power supply, and observe the SYS system indicator light; Connect the SFP optical module for the fiber uplink, and connect the RJ45 port to the PoE terminal device; Enable basic functions such as VLAN isolation and forced 10M long-distance transmission through the device’s jumpers; Download the corresponding APP on an Android phone or access the Web management page through a computer browser to view real-time operating parameters, configure optical power alarm thresholds, and set advanced functions such as timed restart; Read the on-board LED screen to quickly view real-time operating data such as voltage, current, optical power, and temperature. Importance and Key Features In industrial and outdoor deployments, network equipment often faces voltage fluctuations, high and low temperatures, and lightning surges. The core value of this AI PoE switch is to solve the pain points of unstable power supply and difficult equipment status troubleshooting in outdoor and new energy scenarios. This AI PoE switch supports wide-voltage input of 9-54V, has a built-in boost circuit, and can output considerable PoE power even with low-voltage input. All ports have 6KV lightning protection and work temperature ranges from -40°C to +75°C. It supports complete DDM diagnosis for SFP, allows custom optical power alarms, and also supports port or entire machine timed restart. At 10M rate, the maximum transmission distance of the network cable is 250 meters. The AI PoE switch combines convenient deployment with refined operation and maintenance, allowing for both immediate use after unpacking and deep parameter configuration, reducing the difficulty and cost of on-site operation and maintenance. Application Scenarios This AI PoE switch is widely used in intelligent manufacturing automation, power and new energy cluster networking, video surveillance in railway tunnels, on-site communication in oil and gas mines, and also compatible with smart city infrastructure, autonomous driving, humanoid robots, AI computing, outdoor base stations, and outdoor meteorological monitoring scenarios. It is particularly suitable for outdoor locations powered by solar cells. The voltage boosting circuit can solve the problem of voltage fluctuations in the photovoltaic system, and the fiber-optic uplink method can achieve stable data transmission over long distances, meeting the needs of various unmanned stations for 7×24-hour uninterrupted operation. The LNK-AIMC104GMP integrates voltage boosting power supply, AI intelligent monitoring, industrial protection, and fiber-optic uplink in a compact body. This AI PoE switch effectively fills the demand gap for PoE network equipment in harsh environments. Whether for new project setup or existing network renovation, it can provide stable and reliable hardware support for industrial and outdoor networks.

E-link Unveils New Mini Industrial AI Smart Managed Switch Series for Harsh Environments and Solar-Powered Networks Shenzhen, China — E-link, a leading industrial networking solution provider, has officially launched its new-generation Mini Industrial AI Smart Managed Switch series, a family of compact, feature-rich managed switches engineered for intelligent manufacturing, new energy, rail transit, and smart city deployments. The series covers four models: the LNK-AIMC103GM fiber switch, the LNK-AIMC103GMP IEEE 802.3at PoE+ 30W switch, the LNK-AIMC103GMP60 IEEE 802.3bt PoE++ 60W switch, and the LNK-AIMC103GMP90 IEEE 802.3bt PoE++ 90W switch — the latter three featuring a built-in voltage booster specially optimized for solar power supply applications. World-First Managed/Unmanaged Hybrid Design with AI Smart Management Independently developed by E-link, this world-first innovative device combines the dual advantages of managed and unmanaged switches. Engineers can monitor device status through multiple methods — the Android mobile APP, PC web management interface, and one-click LED display dashboard — without additional test tools. Real-time data coverage includes system voltage, current, internal temperature, Ethernet port status, SFP port working status, PoE status, and detailed SFP DDM parameters such as optical power, wavelength, transmission distance, link rate, and module temperature. Key Highlights Self-developed intelligent management system supporting Android mobile APP and PC web UI One-click LED screen real-time data dashboard: system current, voltage, internal temperature, SFP transmit/receive optical power, and link speeds Complete SFP information with DDM diagnostic data and customizable optical power alarm thresholds User-defined scheduled port/device reboot and PoE scheduled restart One-click VLAN isolation and 10M 250m long-distance transmission 6KV lightning surge protection on all ports Wide operating temperature: -40°C to +75°C (-40°F to 167°F) IP40 aluminum housing, DIN-rail mounting, dual redundant power supplies for 24x7 stable operation MTBF > 200,000 hours; ISO9001, CE, FCC Part 15 Class A, and RoHS certified Built-in Voltage Booster for Solar Power Applications The PoE models integrate a built-in voltage boost circuit that converts low-voltage DC input into stable 48V PoE output, making them ideal for solar, wind, and battery-powered off-grid networks: Model PoE Standard PoE Output 12V Input 24V Input 48V Input LNK-AIMC103GMP IEEE 802.3af/at PoE+ 30W max 60W 90W 90W LNK-AIMC103GMP60 IEEE 802.3af/at/bt PoE++ 60W max 60W 120W 180W LNK-AIMC103GMP90 IEEE 802.3af/at/bt PoE++ 90W max 60W 120W 240W All PoE models support Mode A and Mode B power pin assignment (1/2(+), 3/6(-); 4/5(+), 7/8(-)) and are available in customizable versions compatible with Starlink Gen 2 / Gen 3. Interfaces and Performance 3× 10/100/1000Base-T RJ45 ports with auto-negotiation and auto MDI/MDI-X 1× 100/1000BASE-X SFP fiber uplink port, backward compatible with 100BASE-X and 1000BASE-X transceivers Single-mode fiber transmission up to 200km; multi-mode fiber up to 2km 10Gbps non-blocking switching capacity with 9K jumbo frame support Wide 9–54VDC power input via 4-pin terminal block, 5W max consumption (PoE idle) Application Scenarios The series is designed for intelligent manufacturing and automation, power and new energy surveillance communication and cluster networking, rail transit and tunnel engineering real-time video monitoring, oil, gas and mining site stable communication, and smart city and new infrastructure deployment. It is also suitable for emerging fields such as autonomous driving, humanoid robots, AI computing, metallurgy, chemical engineering, outdoor research base stations, and field weather monitoring.

E-link Unveils 90W AI Smart Managed PoE++ Switch with Built-in Voltage Booster for Solar-Powered Industrial Networks SHENZHEN, China \u2014 E-link, a professional manufacturer and exporter of industrial networking equipment, has officially launched the LNK-AIMC103GMP90-SFP, a mini industrial AI smart managed PoE++ Ethernet switch that delivers up to 90W of PoE++ power per port and integrates a built-in voltage boost circuit specially optimized for solar and DC power supply applications. As the latest member of E-link's AI smart managed switch family, the LNK-AIMC103GMP90 is equipped with 3 \u00d7 10/100/1000Base-T RJ45 PoE++ ports and 1 \u00d7 100/1000BASE-X SFP fiber uplink port. It combines the simplicity of unmanaged switches with the intelligence of managed switches, allowing engineers to monitor the whole network without any additional test tools. World-First Design: AI Management Meets Voltage Booster The switch features E-link's self-developed intelligent management system, accessible through an Android mobile APP and PC web UI. A one-click LED screen displays a real-time data dashboard including system current, voltage, internal temperature, SFP transmit/receive optical power, Ethernet and fiber port link speeds, and more. Engineers can also customize optical power alarm thresholds and schedule port or device reboots remotely. Thanks to its built-in voltage booster, the device accepts a wide 9\u201354VDC power input and boosts it into high-power PoE output \u2014 making it ideal for off-grid solar systems, base stations and remote field sites: DC InputMax PoE Output 12V input60W PoE output 24V input120W PoE output 48V input240W PoE output Key Features Compliant with IEEE 802.3af/at/bt PoE++ PSE standard (af: 15.4W, at: 30W, bt Type 3: 60W, bt Type 4: 95W) Rich APP & web management: graphical dashboard, full SFP DDM diagnostic data, customizable alarm thresholds, scheduled PoE restart & system reset Fiber port alarm, one-click VLAN isolation, and 10M 250m long-distance transmission Redundant-mode auto-recovery: automatically forwards packets to the backup port when the destination port is link-down 6KV lightning surge protection on all ports Wide operating temperature -40\u00b0C to +75\u00b0C, IP40 aluminum housing, DIN-Rail mounting Dual redundant power supplies for stable 24\u00d77 operation Customizable versions available for Starlink Gen 2 / Gen 3 compatibility Technical Specifications Access Mode1\u00d7100/1000BASE-X SFP to 3\u00d710/100/1000BASE-T RJ45 PSE Switching Capacity10Gbps, non-blocking PoE BudgetUp to 90W (9\u201354VDC input with voltage booster) Input Power9\u201354V DC, 4-pin terminal block Casing / MountingAluminum case, DIN-Rail (98 \u00d7 67 \u00d7 46 mm, 300g) CertificationsISO9001, CE, FCC Part 15 Class A, RoHS Application Scenarios The LNK-AIMC103GMP90 is engineered for intelligent manufacturing & automation, power & new energy (solar surveillance and cluster networking), rail transit & tunnel engineering, oil, gas & mining sites, smart city and new infrastructure deployment. It can also be applied in autonomous driving, humanoid robots, AI computing, metallurgy, chemical engineering, outdoor research base stations and field weather monitoring. Availability The new switch is available now with a minimum order quantity of 1 piece, delivery within 10\u201315 working days, and a supply capacity of 10,000 pcs/month. As part of the product launch, E-link is offering special launch discount pricing \u2014 please contact our sales team for the latest quotation. OEM/ODM customization and Starlink-compatible versions are also available upon request. About E-link: Founded in 2001, Shenzhen Yilian Xinyun Technology Co., Ltd. (E-link) is a manufacturer and exporter of industrial PoE switches, media converters, video extenders and networking accessories, serving customers in more than 80% of export markets worldwide.

E-link Introduces LNK-AIMC204G Series: Mini Industrial AI Smart Managed PoE++ and Fiber Ethernet Switches with Built-in Voltage Booster Shenzhen, China — E-link, a leading industrial networking solution provider, is proud to announce the launch of its new LNK-AIMC204G Series of mini industrial AI smart managed Ethernet switches. The series consists of four models — LNK-AIMC204GMP60, LNK-AIMC204GMP90, LNK-AIMC204GMP and LNK-AIMC204GM — each engineered to deliver carrier-grade reliability, intelligent management and flexible deployment for the most demanding industrial environments. Four Models, One Powerful Family Model Ethernet Ports Fiber Uplink PoE Standard Max PoE/Port Voltage Booster LNK-AIMC204GMP60 4× 10/100/1000BASE-T 2× 100/1000/2.5GBASE-X SFP IEEE 802.3af/at/bt PoE++ 60W Yes LNK-AIMC204GMP90 4× 10/100/1000BASE-T 2× 100/1000/2.5GBASE-X SFP IEEE 802.3af/at/bt PoE++ 90W Yes LNK-AIMC204GMP 4× 10/100/1000BASE-T 2× 100/1000/2.5GBASE-X SFP IEEE 802.3af/at PoE+ 30W Yes LNK-AIMC204GM 4× 10/100/1000BASE-T 2× 100/1000/2.5GBASE-X SFP — — No Breakthrough Voltage Booster Technology for Solar Power The PoE models integrate a world-first built-in voltage boost circuit, specially optimized for solar power supply applications. The switch accepts a wide 9–54VDC input and boosts it to deliver powerful PoE output: 12V input → 60W PoE output 24V input → 120W PoE output 48V input → up to 240W PoE output (LNK-AIMC204GMP60/GMP90) With IEEE 802.3af/at/bt PoE++ PSE compliance (15.4W / 30W / 60W / 90W per port) and customizable versions compatible with Starlink Gen 2 / Gen 3, the series powers IP cameras, wireless APs, and edge devices directly from solar or battery systems — eliminating the need for separate power infrastructure. AI Smart Management Without Extra Tools Combining the dual advantages of managed and unmanaged switches, the LNK-AIMC204G series lets engineers monitor the entire device status through three effortless methods: the E-link Android mobile APP, PC web UI, and a one-click LED screen real-time dashboard. Monitored data covers system voltage, current, internal temperature, Ethernet port status, SFP working status, PoE status, and complete SFP DDM parameters including optical power, wavelength, transmission distance, link rate and module temperature. Advanced features include fiber port alarm, scheduled system reset, scheduled PoE restart, one-click VLAN isolation, 10M 250m long-distance transmission, and a redundant mode with auto-recover function that automatically forwards packets to the backup port when the destination port link goes down. Customizable optical power alarm thresholds and user-defined scheduled port/device reboot further simplify field maintenance. Built for Harsh Industrial Environments 20Gbps non-blocking switching capacity, 9K jumbo frame support 6KV lightning surge protection on all ports Wide operating temperature: -40°C to 75°C (-40°F to 167°F) IP40 aluminum housing, DIN-Rail mounting, compact 98×67×46mm mini size Dual redundant power supplies for 24×7 stable operation MTBF > 200,000 hours; CE, FCC Part 15 Class A, RoHS, ISO9001 certified Application Scenarios The series is ideal for intelligent manufacturing and automation, power & new energy surveillance networking, rail transit and tunnel engineering video monitoring, oil/gas/mining sites, smart city and new infrastructure deployment — as well as emerging fields such as autonomous driving, humanoid robots, AI computing, metallurgy, chemical engineering, outdoor research base stations and field weather monitoring.

E-link Unveils the LNK-AIMC010G Series — The World's First Mini Industrial AI Smart Managed Ethernet Switch Family Shenzhen, China — E-link, a pioneering force in industrial networking solutions, proudly announces the official launch of its groundbreaking LNK-AIMC010G Series — the world's first mini industrial AI smart managed Ethernet switch family. This innovative product line redefines industrial networking by seamlessly merging the simplicity of unmanaged switches with the intelligence of fully managed ones, all within a remarkably compact 98×67×64mm DIN-rail form factor. A New Paradigm: AI-Powered Smart Management At the core of the LNK-AIMC010G Series lies E-link's self-developed intelligent management system, which empowers engineers with unprecedented visibility and control through three intuitive access methods: Mobile APP (Android) — Real-time monitoring and configuration on the go PC Web UI — Full-featured management via Chrome, Edge, or Opera One-Click LED Display — Instant data dashboard showing system current, voltage, internal temperature, and Ethernet port link speeds Unlike traditional managed switches that require specialized training, the LNK-AIMC010G Series features a lightweight, simplified graphical interface that makes on-site debugging and maintenance accessible even for non-professional operators — drastically reducing deployment time and operational costs. Product Family Overview The LNK-AIMC010G Series comprises four distinct models, each engineered for specific industrial power and connectivity requirements: Model Port Configuration PoE Standard Max PoE Budget Voltage Booster Price (USD) LNK-AIMC010GM 8×GE RJ45 + 2×GE Uplink Non-PoE — — $29.99 LNK-AIMC010GMP 8×GE PoE+ RJ45 + 2×GE Uplink IEEE802.3af/at 30W per port Support $49.99 LNK-AIMC010GMP60 4×GE PoE++ 60W + 4×GE PoE+ 30W + 2×GE Uplink IEEE802.3af/at/bt (Type 3) 60W per port Support $59.99 LNK-AIMC010GMP90 4×GE PoE++ 90W + 4×GE PoE+ 30W + 2×GE Uplink IEEE802.3af/at/bt (Type 4) 90W per port Support $65.90 Lead Time: 10–15 working days for all models in the LNK-AIMC010G Series. Built-in Voltage Booster for Solar and Starlink Integration All PoE models in the series are equipped with E-link's proprietary voltage booster system, enabling flexible PoE power output matched to different DC input voltages. With a 12V input, the system delivers up to 60W of PoE output; with 24V, it scales to 120W; and with 48V, it reaches an impressive 240W total PoE budget. This makes the switches ideal for solar-powered remote installations. Additionally, customizable versions support Starlink Gen2 and Gen3 compatibility, delivering up to 200W PoE output for satellite-powered edge deployments. Engineered for Extreme Environments Designed to thrive in the toughest conditions, the LNK-AIMC010G Series features: Wide Operating Temperature: -40°C to +75°C (-40°F to 167°F) 6KV Lightning Surge Protection on all ports IP40-Rated Aluminum Housing for superior heat dissipation and durability Dual Redundant Power Supplies (9–54V DC) ensuring 24×7 stable operation MTBF exceeding 200,000 hours 20Gbps Non-Blocking Switching Capacity with 1Mbit packet buffer Smart Features That Matter Beyond basic switching, the LNK-AIMC010G Series packs advanced management capabilities: One-Click VLAN Isolation via physical DIP switch 10M 250m Extended Transmission mode for long-distance deployments Scheduled System Reset for automated maintenance cycles PoE Scheduled Restart (PoE models) to remotely power-cycle connected devices Redundant Mode with Auto-Recovery — if a destination port goes link-down, packets are automatically forwarded to the backup port Application Versatility The LNK-AIMC010G Series is purpose-built for a wide array of industrial applications: intelligent manufacturing and automation, power and new energy surveillance, rail transit and tunnel engineering, oil, gas and mining sites, smart city infrastructure, autonomous driving, humanoid robotics, AI computing, outdoor research stations, and field weather monitoring. With certifications including ISO9001, CE, FCC Part 15 Class A, and RoHS, the series meets global regulatory requirements for deployment in any region. Availability: The LNK-AIMC010G Series is now available for order at competitive factory-direct pricing starting from just $29.99 USD. DIN-rail mounting brackets are included by default. Power supplies are sold separately, with options ranging from 24W to 240W to match specific deployment requirements.

E-link Unveils the LNK-AIPSE301M Series — The World's First AI Smart PoE Injector with Built-In LED Screen Display Shenzhen, China — E-link, an established manufacturer of industrial networking solutions, officially announces the global launch of the LNK-AIPSE301M series, a revolutionary family of AI Smart PoE (Power over Ethernet) Injectors that combine the world's first integrated LED screen display with intelligent real-time power diagnostics. The series is available in three configurations — 30W (PoE+), 60W (PoE++), and 90W (PoE++) — offering a scalable solution for security surveillance, digital signage, wireless networking, and industrial automation. Product Lineup & Competitive Pricing Model PoE Standard Max PoE Budget Access Mode FOB Price (USD) LNK-AIPSE301M30 IEEE802.3af/at (PoE+) 30 Watts Gigabit RJ45 PSE $12.00 – $15.00 LNK-AIPSE301M60 IEEE802.3af/at/bt (PoE++) 60 Watts Gigabit RJ45 PSE $22.00 – $25.00 LNK-AIPSE301M90 IEEE802.3af/at/bt (PoE++) 90 Watts Gigabit RJ45 PSE $22.00 – $25.00 World-First AI Smart LED Display — Visual Diagnostics Without Tools The standout innovation is the one-click LED screen display, an industry-first in a PoE injector. This integrated intelligent dashboard provides instantaneous visibility into five critical operating parameters: PSE Supply Voltage — Real-time output voltage monitoring PoE Class Detection — Automatic IEEE802.3 class identification (Class 0–8) Mode A & Mode B Class — Independent monitoring for both End-span and Mid-span delivery PSE Power Consumption — Live wattage draw from connected powered devices Internal Temperature — Continuous thermal monitoring for proactive maintenance This visual intelligence dramatically accelerates on-site troubleshooting — installers verify power delivery integrity at a glance, a decisive advantage for large-scale deployments. Full-Spectrum IEEE802.3 Standards Coverage The series spans the complete PoE standards range: The LNK-AIPSE301M30 supports IEEE802.3af (15.4W) and IEEE802.3at PoE+ (30W) — ideal for standard IP cameras, VoIP phones, wireless access points, and entry-level IoT devices. The LNK-AIPSE301M60 and LNK-AIPSE301M90 add IEEE802.3bt PoE++ support, delivering up to 60W and 90W for PTZ speed domes, all-in-one touch PCs, remote digital signage, and industrial IoT gateways. All models are backward compatible with 802.3af and 802.3at standards. Power delivery uses Mode A (End-span) on pins 1/2(+), 3/6(-) and Mode B (Mid-span) on 4/5(+), 7/8(-). Passive PoE is available upon request. Gigabit Performance & Industrial-Grade Build Each injector features a 10/100/1000BASE-T Gigabit RJ45 interface with auto-negotiation and auto MDI/MDI-X, using store-and-forward switching for wire-speed forwarding at 1,488,000 pps. Full compliance with IEEE 802.3, 802.3u, 802.3ab, 802.3x (flow control), and 802.3az Energy Efficient Ethernet (EEE) ensures interoperability across diverse network environments. Transmission reaches 100m at Gigabit speed and up to 250m at 10Mbps over Cat 5e or above cabling. The compact ABS+PC casing (146 * 60 * 37 mm, 400g) supports wall-mounting. With an MTBF exceeding 200,000 hours and dual redundant power supply design, the series is built for 24/7 mission-critical operation in temperatures from -10°C to 60°C. Multi-Layer Intelligent Protection Over-Voltage, Over-Load, Over-Temperature & Short Circuit Protection 1KV Lightning Surge Protection on all RJ45 ports 500W Power Surge Protection with 4KV/8KV ESD Protection Limited Power Source (LPS) Compliance Ultra-Low No-Load Power Consumption below 0.5W Technical Specifications Parameter Specification (All Models) PoE Standards IEEE802.3af/at (30W); IEEE802.3af/at/bt (60W & 90W) Data Rate 10/100/1000 Mbps (Gigabit) Input Power 85–265V AC, 50/60Hz (Wide Range) Transmission 100m @ 1000M / 250m @ 10M (Cat 5e+) Dimensions / Weight 146 * 60 * 37 mm / 400g (Wall-Mount) Operating Temp -10°C to 60°C; Storage: -40°C to 85°C Certifications ISO9001, CE, FCC Part 15 Class A, RoHS, EN55022 Class A MTBF > 200,000 hours LED Display AI Smart Dashboard: Voltage, Class, Power, Mode A/B, Temperature Key Applications PTZ Speed Dome Cameras — High-power pan-tilt-zoom surveillance AIO (All-in-One) Touch PCs — Interactive kiosks, POS terminals, digital wayfinding Remote Digital Signage Displays — Large-format advertising without separate AC wiring Wireless Access Points & Bridges — Extended coverage in warehouses, campuses, and outdoor venues Industrial IoT Gateways — Simplified smart factory and automation deployments Availability & Ordering The E-link LNK-AIPSE301M series is in stock for immediate global shipment. FOB pricing starts at $12.00–$15.00 USD (30W) and $22.00–$25.00 USD (60W/90W), with volume discounts available. Custom OEM/ODM configurations — including passive PoE variants — are supported. About E-link: A trusted manufacturer specializing in industrial networking equipment — PoE injectors, PoE switches, media converters, and fiber optic solutions. ISO9001 certified with CE, FCC, and RoHS compliance.

E-link LNK-AIMC104 Series: Complete Mini Industrial AI Smart Managed Fiber Ethernet Switch Portfolio E-link, an innovative manufacturer of industrial networking solutions based in China, has officially launched the complete LNK-AIMC104 series — a versatile family of mini industrial AI smart managed fiber Ethernet switches. The portfolio spans four distinct configurations from an entry-level non-PoE fiber switch to a flagship 90W PoE++ model, providing a one-stop solution for industrial networking needs across IIoT, renewable energy, smart manufacturing, and smart city applications. Four Models to Match Every Application Model PoE Standard PoE Budget Voltage Booster Price LNK-AIMC104GM-SFP Non-PoE N/A × $19.99 LNK-AIMC104GMP30-SFP IEEE802.3af/at 30W √ $29.90 LNK-AIMC104GMP60-SFP IEEE802.3af/at/bt 60W √ $57-72 LNK-AIMC104GMP90-SFP IEEE802.3af/at/bt 90W √ $62-77 AI Smart Management — Industry First All LNK-AIMC104 models feature E-link's proprietary AI smart management system, accessible via Android mobile APP and PC Web UI. Engineers can monitor full device status — including system voltage, current, temperature, Ethernet port status, SFP fiber port working parameters, and complete DDM diagnostics (optical power, wavelength, transmission distance, link rate) — without additional test tools. The one-click LED display dashboard provides real-time data directly on the device, combining the simplicity of unmanaged switches with the visibility of fully managed infrastructure. Built-in Voltage Booster for Solar Applications The PoE models (30W/60W/90W) incorporate a patented voltage boost circuit optimized for solar power supply and battery-operated deployments: 9-12VDC Input → 48V PoE Output, max 60W 19-24VDC Input → 48V PoE Output, max 120W 48-54VDC Input → 48V PoE Output, max 120W/240W PoE Mode A and Mode B are both supported and switchable via the management interface. Customizable versions for Starlink Gen 2 (150W) and Gen 3 (200W) compatibility are available. Key Features Across All Models Port Configuration: 4* 10/100/1000Base-T RJ45 + 1* 100/1000BASE-X SFP fiber uplink Fiber Port Alarm: Customizable optical power thresholds with LED alert and APP notification Scheduled Reset: User-defined periodic port and system reboot via management interface One-Click VLAN Isolation: Hardware DIP switch or software-controlled port isolation 10Mbps 250m Extended Transmission: Long-distance copper connectivity for remote endpoints 20Gbps Non-Blocking Switching Capacity: Store-and-forward architecture with 1Mbit packet buffer 6KV Lightning Surge Protection: All ports protected for outdoor and industrial environments Dual Redundant Power Input: 9-54VDC, 4-pin terminal block, 24*7 stable operation Industrial-Grade Durability: IP40 aluminum housing, -40°C to +75°C operating temperature Compact Design: 98 * 67 * 46 mm, 300g, DIN-Rail mountable Certifications: ISO9001, CE, FCC Part 15 Class A, RoHS Application Scenarios The LNK-AIMC104 series is engineered for mission-critical deployments across diverse industries: Intelligent Manufacturing & Automation: Data transmission and multi-device interconnection on factory floors Power & New Energy: Solar/wind farm surveillance communication and cluster networking Rail Transit & Tunnel Engineering: Real-time video monitoring and signal transmission in extreme conditions Oil, Gas & Mining: Stable communication in hazardous and remote locations Smart City & New Infrastructure: IoT sensor networks, traffic management, public safety systems Autonomous Driving & AI Computing: Low-latency data links for edge computing and V2X communication Outdoor Research Stations & Weather Monitoring: Reliable networking in harsh field environments Availability All four LNK-AIMC104 models are in stock with a supply capacity of 10,000 pcs/month. Minimum order quantity is 1 piece — sample orders are welcome. Delivery time is 10-15 working days. Payment accepted via L/C, T/T, and Western Union. SFP modules and power supplies are to be purchased separately with multiple options available. For detailed specifications, pricing inquiries, or to request a sample unit, please contact the E-link sales team.

E-link Launches Next-Generation Mini Industrial AI Smart Managed PoE++ Ethernet Switch Series China, July 2026 — E-link, a leading provider of industrial networking solutions, proudly announces the official launch of its LNK-AIMC103GMP series — a groundbreaking family of Mini Industrial AI Smart Managed PoE++ Ethernet Switches with built-in voltage booster. Specifically engineered for harsh outdoor and industrial environments, this series is now available in three distinct power configurations to meet diverse deployment requirements: 30W (IEEE 802.3at PoE+), 60W (IEEE 802.3bt PoE++), and 90W (IEEE 802.3bt PoE++ high-power). Three Models, One Powerful Platform The LNK-AIMC103GMP series consists of three compact yet powerful models, each delivering a unique PoE power budget to power a wide range of connected devices — from IP cameras and wireless access points to high-power PTZ cameras and outdoor Starlink terminals: Model PoE Standard PoE Budget Price Range (USD) LNK-AIMC103GMP30-SFP IEEE 802.3af/at PoE+ Up to 30W $52 – $67 LNK-AIMC103GMP60-SFP IEEE 802.3af/at/bt PoE++ Up to 60W $57 – $72 LNK-AIMC103GMP90-SFP IEEE 802.3af/at/bt PoE++ Up to 90W $62 – $77 All three models share a common hardware platform featuring 3x 10/100/1000Base-T RJ45 PoE ports plus 1x 100/1000BASE-X SFP fiber uplink port, housed in a rugged aluminum casing measuring just 98 x 67 x 46 mm and weighing only 300g. The DIN-rail form factor makes installation quick and seamless in any control cabinet or outdoor enclosure. World-First Innovation: AI Smart Management with Mobile APP & LED Dashboard What truly sets the LNK-AIMC103GMP apart is E-link's self-developed AI Smart Management System, which combines the simplicity of an unmanaged switch with the powerful diagnostics of a managed switch. Engineers can monitor real-time device status through three intuitive channels: Android Mobile APP — Full device management from anywhere, with graphical dashboards displaying voltage, current, temperature, port status, PoE power consumption, and SFP DDM diagnostic data PC Web Management Interface (macOS & Windows) — Compatible with Edge 89+, Chrome 89+, and Opera 75+ browsers One-Click LED Display — Instant on-device data readout of system current, voltage, internal temperature, SFP optical power, and link speeds — no test tools required Advanced management features include fiber port alarm, scheduled system reset, PoE scheduled restart, one-click VLAN isolation, 10M 250m extended transmission, and network redundancy with auto-recovery. Customizable optical power alarm thresholds provide proactive fault detection for mission-critical fiber links. Built for Solar: Integrated Voltage Booster A standout feature of this series is the built-in voltage boost circuit, specially optimized for solar-powered and battery-operated applications. The ultra-wide 9-54VDC input range accepts almost any DC power source, while the internal booster guarantees stable PoE output regardless of input fluctuations: 12V input → 60W PoE output 24V input → 90W PoE output 48V input → 90W PoE output This makes the LNK-AIMC103GMP series an ideal choice for remote solar-powered surveillance stations, off-grid communication towers, and renewable energy monitoring systems where traditional AC power is unavailable. Industrial-Grade Reliability Built to perform in the toughest conditions, each switch in the series is rated for -40C to +75C operating temperature, features 6KV lightning surge protection on all ports, and meets IP40 protection standards. Dual redundant power inputs ensure 24/7 uninterrupted operation. The series carries ISO9001, CE, FCC Part 15 Class A, and RoHS certifications. Versatile Application Scenarios The LNK-AIMC103GMP series is purpose-built for a wide spectrum of industrial and infrastructure applications: Intelligent Manufacturing & Automation — Multi-device interconnection and real-time data transmission on factory floors Power & New Energy — Solar farm surveillance communication and wind turbine cluster networking Rail Transit & Tunnel Engineering — Real-time video monitoring and signaling transmission Oil, Gas & Mining — Stable communication in explosive and remote environments Smart City & Infrastructure — Intelligent traffic systems, smart street lighting, and public safety networks Starlink & Satellite Communication — Customizable PoE pin assignments for Starlink Gen 2 and Gen 3 terminal compatibility (up to 200W output for Gen 3) Autonomous Driving, AI Computing & Robotics — Rugged edge networking for next-generation autonomous systems Availability and Ordering The LNK-AIMC103GMP series is available for immediate order with a minimum order quantity of 1 piece. Standard delivery time is 10-15 working days, with a monthly supply capacity of 10,000 units. Each unit ships with a default DIN-rail mounting bracket; SFP modules and power supplies are available separately to allow maximum configuration flexibility. Payment is accepted via L/C, T/T, and Western Union. For more information or to request a sample, please visit the E-link website or contact our sales team directly.

E-link Launches Industrial Gigabit 802.3bt PoE++ Splitter with LED Display and Adjustable Output Voltage Shenzhen, China – E-link, a trusted manufacturer of industrial networking solutions, has officially unveiled its latest innovation: the LNK-INS901-LED Industrial Gigabit 802.3bt PoE++ Splitter. Designed to address the growing demand for flexible, high-power connectivity in harsh environments, this new device separates power and data from a single PoE input cable and delivers adjustable DC output from 5V to 36V — all managed through a built-in LED display for real-time monitoring. Meeting the Needs of Modern Industrial Networks As industrial IoT deployments continue to scale, system integrators and facility managers increasingly face the challenge of powering non-PoE devices in locations where AC outlets are unavailable or impractical. The LNK-INS901-LED solves this problem elegantly by converting a standard IEEE 802.3af/at/bt PoE++ input into regulated DC power and Gigabit Ethernet data output, eliminating the need for separate electrical wiring to remote edge devices such as IP cameras, wireless access points, sensors, and access control terminals. Our customers told us they needed a PoE splitter they could trust in extreme conditions — one that not only delivers reliable power but also gives them visibility into what is happening at the edge. The LNK-INS901-LED brings that transparency with its scrolling LED display, showing temperature, power, voltage, and current at a glance. Key Features and Technical Highlights Comprehensive PoE Support: Fully compatible with IEEE 802.3af (PoE), 802.3at (PoE+), and 802.3bt (PoE++) standards, ensuring maximum flexibility across different power sourcing equipment. Adjustable DC Output: Delivers 5V to 36V DC adjustable output via a convenient rotary knob, with maximum 70W power delivery, supporting a broad range of non-PoE terminal devices. Built-in LED Display: A scrolling LED screen continuously monitors key operational metrics — temperature (°C), power (W), voltage (V), and current (A) — enabling proactive maintenance and rapid diagnostics. Gigabit Data Throughput: Equipped with one RJ45 PoE input port and one RJ45 data output port, both supporting 10/100/1000Base-T for full Gigabit speed. Rugged Industrial Design: Housed in an IP40-rated aluminum case with fanless cooling, the unit operates reliably in extreme temperatures ranging from -40°C to 80°C (-40°F to 176°F). Flexible Installation: Supports both DIN-Rail and wall-mount installation, with a default DIN-Rail bracket and a wall mount bracket included in the package. Short-Circuit Protection: Built-in short-circuit protection for power output ensures safe operation and device longevity. Extended Reach: Maintains full data and power transmission over Cat5e or above UTP cable up to 100 meters. Technical Specifications at a Glance Parameter Specification PoE StandardIEEE 802.3af/at/bt Ethernet StandardsIEEE 802.3 10Base-T, 802.3u 100Base-TX, 802.3ab 1000Base-T PoE Input Port1 * RJ45 10/100/1000Base-T (Data + Power) Data Output Port1 * RJ45 10/100/1000Base-T DC Output5V to 36V DC adjustable, max 70W DC Output Connector1 * 4-Pin removable terminal block LED DisplayTemperature (°C), Power (W), Voltage (V), Current (A) Forward Filter Rate1,488,000 pps (1000Mbps) Max Distance100m over Cat5e UTP or above Dimensions95 * 70 * 30 mm Weight0.25 kg CasingAluminum (IP40, fanless) Operating Temperature-40°C to 80°C (-40°F to 176°F) Storage Temperature-40°C to 85°C (-40°F to 185°F) Relative Humidity5% to 95% non-condensing MTBF>200,000 hours MountingDIN-Rail / Wall-mount (both included) CertificationsISO9001, CE, FCC Part 15 Class A, RoHS Ordering and Availability Model Description LNK-INS901-LED Industrial IEEE 802.3af/at/bt Gigabit PoE Splitter with LED Display, Output Voltage 5V to 36V DC adjustable, max output 70W, DIN-Rail and Wall-mount installation Pricing: $42 – $47 per unit | MOQ: 1 PCS | Supply Ability: 10,000 pcs/month | Delivery: 10–15 working days | Payment Terms: L/C, T/T, Western Union. About E-link E-link is a leading manufacturer of industrial networking and communication equipment, specializing in PoE switches, PoE splitters, media converters, and fiber optic solutions. With ISO9001-certified manufacturing facilities and products certified to CE, FCC, and RoHS standards, E-link serves customers across more than 50 countries. The company is committed to delivering reliable, cost-effective connectivity solutions for smart cities, intelligent transportation, factory automation, and energy management applications. For more information about the LNK-INS901-LED or to request a sample, please visit the E-link website or contact the sales team directly.

E-link Launches Next-Generation LNK-AIMC005GMP Industrial AI Smart Managed PoE+ Switch with Voltage Booster E-link, a leading provider of industrial networking solutions, is proud to announce the launch of its LNK-AIMC005GMP — a compact yet powerful Industrial AI Smart Managed PoE+ Ethernet Switch featuring a built-in Voltage Booster, designed specifically for solar-powered systems, Starlink deployments, and harsh outdoor environments. Key Features and Innovations The LNK-AIMC005GMP is a 5-port 10/100/1000BASE-T Gigabit Ethernet switch with 4 PoE+ ports supporting IEEE 802.3af/at up to 30W per port. Its standout innovation is the integrated Voltage Booster, which enables flexible DC input ranging from 9V to 54V while delivering stable 48V PoE output — ideal for solar battery systems and off-grid installations. Intelligent Power Management Voltage Booster Technology: Converts low-voltage DC input (as low as 9V) to 48V PoE output, delivering up to 120W total PoE power budget depending on input voltage levels. Dynamic Input Range: 12V input → 60W PoE output | 24V input → 120W PoE output | 48V input → 120W PoE output. Mode A & B Switchable: End-span + Mid-span PoE power delivery, supporting both Mode A (1/2+, 3/6-) and Mode B (4/5+, 7/8-), switchable through the management interface. AI Smart Managed Platform The switch comes with a comprehensive AI Smart Managed web-based dashboard accessible via PC (MacOS/Windows browsers) and Android mobile app, offering real-time monitoring of: Monitoring Feature Description Service Board StatusReal-time temperature, voltage, and current monitoring Per-Port PoE ControlPSE status, active pairs, supply voltage, and power consumption per port RJ45 Port StatusLink status, current rate, and connection diagnostics Restart PoERemote PoE reboot for connected devices Scheduled ResetTime-based automatic device restart Port PoE Scheduled RestartIndividual port-level scheduled reboot for maximum flexibility Built for Extreme Environments Wide Operating Temperature: -40°C to +75°C (-40°F to 167°F), suitable for outdoor and industrial deployments worldwide. 6KV Lightning Surge Protection: All ports equipped with robust surge protection, ensuring reliable operation during electrical storms. Industrial-Grade Build: Aluminum casing with DIN-Rail mounting, compact dimensions of 98 x 67 x 46 mm, and a lightweight design at only 320g. High Reliability: MTBF exceeding 200,000 hours, with switching capacity of 20Gbps (non-blocking). Starlink & Solar System Compatibility The LNK-AIMC005GMP is fully compatible with Starlink Gen2 and Gen3 terminals, making it the perfect power and connectivity solution for remote communication sites. Combined with its wide DC input range, it seamlessly integrates into solar-powered networks where traditional AC power infrastructure is unavailable. Ordering & Availability Specification Detail Model NumberLNK-AIMC005GMP Unit Price$29.90 Minimum Order Quantity1 PCS Supply Ability10,000 pcs/month Delivery Time10-15 Working Days Payment TermsL/C, T/T, Western Union CertificationsISO9001, CE, FCC Part 15 Class A, RoHS About E-link E-link is a trusted manufacturer of industrial networking equipment, specializing in PoE switches, media converters, and fiber optic solutions. With a commitment to quality, innovation, and customer satisfaction, E-link products are deployed in mission-critical applications across telecommunications, security surveillance, smart transportation, and renewable energy sectors worldwide. For more information or to place an order, please visit our website or contact our sales team.

E-link Introduces the LNK-AI3011M-SFP: AI-Driven Smart Managed Fiber Media Converter E-link China Technology Co., Ltd., a leading innovator in fiber optic communication solutions, proudly announces the launch of the LNK-AI3011M-SFP AI Smart Managed Fiber Media Converter. This next-generation device integrates artificial intelligence with industrial-grade media conversion, delivering an unprecedented level of intuitive management and real-time diagnostics for mission-critical network infrastructures. Revolutionizing Network Management with AI Unlike traditional media converters that require specialized test instruments and technical expertise for troubleshooting, the LNK-AI3011M-SFP empowers users with a mobile APP and PC-based intelligent web management platform. This innovative approach eliminates the dependency on external diagnostic tools, enabling both professionals and non-specialists to monitor and maintain fiber optic networks with ease. One-Click Comprehensive Diagnostics With a single tap, users can access a wealth of real-time operational data: System Parameters: Operating current, voltage, and temperature Optical Module Metrics: Transmit power, receive power, and all DDM (Digital Diagnostics Monitoring) information Port Status: Ethernet and fiber port link status, data rates, and LFP (Link Fault Pass-Through) status Intelligent APP and Web Management Features Feature Description Graphical Device Dashboard Intuitive visual presentation of detailed device information and operational status SFP Module Intelligence Comprehensive SFP module parameters including optical power, wavelength, transmission distance, data rate, and temperature Customizable Alarm Thresholds User-defined optical power thresholds with multi-level alerts Scheduled Maintenance User-defined scheduled reboot for automated network maintenance Multi-Method Alarms Real-time alarm notifications via multiple channels for immediate fault response Built for Critical Applications The LNK-AI3011M-SFP is engineered to excel in the most demanding environments. Its rugged aluminum casing, wide operating temperature range (-20°C to 70°C), and robust design make it the ideal choice for: Forest Fire Prevention Systems Water Area Monitoring Networks Highway and Urban Road Surveillance Rail Transit Communication High-End Office Building Infrastructure Petrochemical Facility Monitoring Automated Equipment Communication and Control High-Performance Specifications The converter features 1 x 100/1000Base-X SFP port (with auto-detection) to 1 x 10/100/1000BASE-T RJ45 Ethernet port, supporting store-and-forward processing at wire-speed rates up to 1,488,000 packets per second. With a 9K jumbo frame capability and compliance with IEEE 802.3/802.3u/802.3ab/802.3z standards, it ensures seamless integration into any existing network architecture. Specification Detail Dimensions 93 x 71 x 29 mm Weight 100g Power Input 5~58V DC (AC-DC adapter included) Power Consumption 3W Max MTBF > 200,000 hours Fiber Distance (Single Mode) Up to 200 km Certifications ISO9001, CE, FCC Part 15 Class A, RoHS Intelligent Alarm System The device incorporates a sophisticated LED indicator system with dedicated status lights for power, Ethernet link/activity, SFP link/activity, and fiber port alarms. The Fiber Port Alarm (F1 ALM) provides three-level optical power monitoring: red for below-threshold, orange for near-threshold, and off for normal operation. Combined with Link Fault Pass-Through (LFP) functionality, network administrators can instantly identify and locate fiber link failures. Cost-Effective, Future-Ready Networking "The LNK-AI3011M-SFP represents a paradigm shift in media converter technology," said the E-link product team. "By integrating AI-driven intelligence into a compact, cost-effective form factor, we are enabling businesses of all sizes to deploy and maintain professional-grade fiber optic networks without the traditional overhead of specialized training and expensive diagnostic equipment." The LNK-AI3011M-SFP AI Smart Managed Fiber Media Converter is available now. SFP modules are sold separately, with a comprehensive range of options covering multi-mode (550m to 2km) and single-mode (20km to 200km) fiber distances. For more information, visit www.e-linkchina.com.cn or contact the sales team at sales@e-linkchina.com.